Analysis of Slag-Containing Steamed Concrete's Composition Efficiency.

Thermal power plant slag is a waste that is presently obtained from many power stations all over the world. A possible method for its utilization is using it to produce concrete. This paper analyses the effect of thermal power plant slag on the technological properties of concrete mixtures and the mechanical properties of concrete subjected to heat-moisture processing. Quantitative estimates of the investigated factors' influence on the concrete mixture's water demand and the strength of steamed concrete were obtained. The influences of TPP slag content and its water demand on concrete composition features as well as concrete strength are shown. The novelty of the work lies in the use of an experimental-statistical model to optimize the composition of steamed concrete using slag from the viewpoint of maximum strength per kilogram of cement. It has been demonstrated that the optimal part of slag in aggregate, which provides maximum strength at 4 h and 28 days after steaming, is 0.5-0.55 and 0.45-0.55, respectively. A method for the design of concrete composition using slag from thermal power plants is proposed.

Determining Compressed Concrete Element Limit States Based on the Widths and Depths of Cracks Caused by Transverse Deformations.

In the modern theory of compressed concrete elements, the most attention is paid to longitudinal deformations, whereas transverse ones are rarely considered and just within Poisson's coefficient limits (i.e., elastic concrete behavior in the transverse direction). However, transverse deformations significantly develop beyond the limits corresponding to Poisson's coefficient, where they lead to longitudinal crack initiation and development. In-depth experimental and numerical investigations of transverse deformations in the inelastic stage showed that it is necessary to consider crack propagation. The present study proposes simultaneous consideration of longitudinal and transverse deformations, as well as the appearance of cracks and their widths and depths. This allowed us to obtain a complete compressed concrete element behavior pattern at all performance stages in two types of limit states (based on longitudinal and transverse deformations). Consequently, new ultimate limit states by the depth and width of cracks caused by transverse deformations are proposed to be included in modern design practices and codes.

Investigation of the Cementing Efficiency of Fly Ash Activated by Microsilica in Low-Cement Concrete.

This paper presents experimental results on the influence of concrete composition factors on the criterion characterizing the ratio between the compressive strength of activated low-cement concrete and clinker consumption. The investigation was carried out using mathematical planning of the experiments. Experimental and statistical models describing the influence of the fly ash, activating additive (microsilica), consumption of cement and aggregates, as well as the superplasticizer on the strength of low-cement concrete under normal hardening conditions and after steaming were obtained. The values of the clinker efficiency criterion and the mineral additive cementing efficiency coefficient were calculated, and models of these parameters were obtained for the investigated concrete compositions. It was shown that the activating effect of microsilica yields an increase in ash cementing efficiency and clinker efficiency criterion in concrete. Using the obtained models, an example for calculating the ash cementing efficiency coefficient is given.

The Influence of Polymer Superplasticizers on Properties of High-Strength Concrete Based on Low-Clinker Slag Portland Cement.

The paper deals with the effectiveness of various types of polymers (naphthalene formaldehyde, polycarboxylate, and lignosulfonate) as superplasticizers of concrete mixtures based on low-clinker slag Portland cement. Using the mathematical planning experimental method and statistical models of water demand of concrete mixtures with polymer superplasticizers, as well as concrete strength at different ages and under different curing conditions (normal curing and after steaming) were obtained. According to the models, the superplasticizer's water-reducing effect and relative change in concrete strength were obtained. The proposed criterion for evaluating the effectiveness and compatibility of superplasticizers with cement takes into account the water-reducing effect of the superplasticizer and the corresponding relative change in concrete strength. The results demonstrate that the use of the investigated superplasticizer types and low-clinker slag Portland cement allows for achieving a significant increase in concrete strength. The effective contents of various polymer types, which allow the achieving of concrete strengths from 50 MPa to 80 Mpa, has been found.

Experimental Verification of Theoretical Stress-Strain Model for Compressed Concrete Considering Post-Peak Stage.

The theoretical stress-strain model for compressed composite cement materials' behavior without empirical coefficients was proposed by Iskhakov in 2018. This model includes the following main parameters describing concrete behavior: stresses and strains corresponding to the border between the elastic and non-elastic behavior stages of a concrete specimen, ultimate elastic strains, and stresses and strains at the end of the post-peak region. Particular attention is focused on the descending branch of the stress-strain diagram, as well as on the analysis of concrete elastic and plastic potentials. These potentials are important for assessing the dynamic response of the concrete element section, as well as for concrete creep analysis. The present research is aimed at experimental verification of the above-mentioned theoretical model. The obtained experimental results are in good agreement with the theoretical ones, which confirms the model's accuracy and enables a significant reduction in the empirical coefficients number in compressed reinforced concrete elements design. This, in turn, represents the scientific novelty of this study.

Using Experimental Statistical Models for Predicting Strength and Deformability of Self-Compacting Concrete with Ground Blast-Furnace Slag.

Ground blast-furnace slag is one of the waste products available in Ukraine and other countries. It is obtained at metallurgical enterprises in huge quantities and can be efficiently used for concrete production. The article is devoted to obtaining experimental-statistical models of the influence of technological factors that determine the composition of self-compacting concrete (SCC) based on ground blast-furnace slag and polycarboxylate superplasticizer on compressive strength, tensile strength, prismatic strength, elastic modulus and crack resistance. Analysis of the investigated factors' influence on the specified SCC properties is carried out and positive influence of blast-furnace slag and superplasticizer simultaneous action on durability and deformation characteristics is studied. A design method of SCC composition design using the obtained mathematical models is developed. It allows for the consideration of a set of necessary parameters simultaneously. A numerical example is given.

Combining an Intensive Green Roof with Seismic Retrofitting of Typical Reinforced Concrete Buildings in Israel.

This study suggests an intensive green roof as part of a sustainable and hazard-resistant conceptual design for the retrofitting of old buildings in Israel. The roof is suggested to be built with waste-based materials. A five-story reinforced concrete residential building was retrofitted with: Case 1: concrete wall strengthening (CWS)-conventional concrete + conventional green roof; Case 2: CWS-waste-included concrete + waste-based green roof; Case 3: seismic isolation columns (SIC)-conventional concrete + conventional green roof; and Case 4: SIC-waste-included concrete + waste-based green roof. Palekastro, Nuweiba, Tabas, and Erzincan ground motions were used for a structural dynamic time-history analysis of the retrofitted buildings. Life cycle assessments of cases 1-4 were performed using ReCiPe 2016 midpoint and endpoint evaluations. A two-stage analysis of variance (ANOVA) was used to analyze the ReCiPe endpoint results. According to the seismic results, Case 3 and Case 4 were much more preferable to Case 1 and Case 2, whereas according to the environmental evaluations, Case 4 was the most preferable to the other cases.